| ??? 02/20/09 11:15 Modified: 02/20/09 12:34 Read: times |
#162589 - That means you get Responding to: ???'s previous message |
Mahmood Elnasser said:
I'm using 1 master that is enabled all the time transmitting data to 7 slaves that are set as receivers only.
the problem is when I put a terminating resistor of 120 Ohms I don't get the data received correctly but when I remove it the communication is ok. What is the problem. I actually tested it with 1 master and 1 slave only so far. I used MAX483 for all master and slaves with the master DE enabled and the slaves RE enabled for I need 1 way communications. Mahmood That means you get reflections with 120 Ohm Resistance .Which indicates the characteristic Impedance of your transmission line is NOT EQUAL to 120 Ohm. A slight impedance mismatch may not be a problem. There is no hard n fast rule to always select a 120 Ohm resistance to get things going.Actually If you have very long cable and are experiencing noise problem withot the[EDIT] proper [/EDIT] Termination resistances you can use one (within reason)and when required . Regards/ Ap |
| Topic | Author | Date |
| RS485 problem | 01/01/70 00:00 | |
| Just 1? | 01/01/70 00:00 | |
| The 120 ohm resistor | 01/01/70 00:00 | |
| VCC = 5V | 01/01/70 00:00 | |
| you need | 01/01/70 00:00 | |
| Scope? | 01/01/70 00:00 | |
| daisy chain | 01/01/70 00:00 | |
| Some hints... | 01/01/70 00:00 | |
| 100 meters | 01/01/70 00:00 | |
| 7 clocks | 01/01/70 00:00 | |
| Topology | 01/01/70 00:00 | |
| RE: topology | 01/01/70 00:00 | |
| don't | 01/01/70 00:00 | |
| Yes, don't! | 01/01/70 00:00 | |
| Getting there | 01/01/70 00:00 | |
| So, what was the cause of failure? | 01/01/70 00:00 | |
| not yet | 01/01/70 00:00 | |
| with additional components | 01/01/70 00:00 | |
| Where do you have this circuit from? | 01/01/70 00:00 | |
| from my Mentor | 01/01/70 00:00 | |
| Ben's site | 01/01/70 00:00 | |
| Mission Accomplished | 01/01/70 00:00 | |
| I'm not sure I agree | 01/01/70 00:00 | |
| exactly | 01/01/70 00:00 | |
| Maybe I misunderstood your earlier post | 01/01/70 00:00 | |
no | 01/01/70 00:00 | |
| yes | 01/01/70 00:00 | |
| then how could you ask .. | 01/01/70 00:00 | |
| With noise+etc reduction | 01/01/70 00:00 | |
| email updated | 01/01/70 00:00 | |
| here's info's........ | 01/01/70 00:00 | |
| That means you get | 01/01/70 00:00 | |
| Only when seeing nosie? | 01/01/70 00:00 | |
| Not exactly but as per requirement | 01/01/70 00:00 | |
| CAT5 ethernet cable | 01/01/70 00:00 | |
| 100 Ohm | 01/01/70 00:00 | |
| More details here | 01/01/70 00:00 | |
| did you check the FAQ? | 01/01/70 00:00 |