Email: Password: Remember Me | Create Account (Free)

Back to Subject List

Old thread has been locked -- no new posts accepted in this thread
???
12/27/08 20:14
Read: times


 
#161177 - Crystals
Responding to: ???'s previous message
One of the parts I was hoping to scavenge from the clock radio was a crystal to use as a clock on my 8051. Looking at the schematic of the 8650, I saw that pin 27 was the clock and off that line was a resistor and a thing that looked like a pancake capacitor but was green, shiny and square with rounded edges. There are a lot of these throughout the boards in this clock radio and I'm not sure if they're crystals or caps. They are labeled C### just like the other capacitors are on the boards, but I'm hoping that they're crystals that I can use to drive the 8051. Here are some part numbers if anyone knows what they are (google gave too much info with too little of it useful):

561J G2A
2A 152
2A 473K
2A 103JT (this is the one off pin 27 of the clock IC)
2A 333K

List of 40 messages in thread
TopicAuthorDate
Help with 4 digit LED 7 segment display            01/01/70 00:00      
   common cathode            01/01/70 00:00      
   Maybe it is a standard display            01/01/70 00:00      
      It's standard, but I can't find a spec sheet            01/01/70 00:00      
         an old-time part, perhaps?            01/01/70 00:00      
            The 8650 is a standard alarm clock IC            01/01/70 00:00      
               add up the forward voltages, adjust the resistors ...            01/01/70 00:00      
                  Diagram            01/01/70 00:00      
                     It's all up to you ...            01/01/70 00:00      
                        Too soon to start worrying about voltage            01/01/70 00:00      
                           Be careful ... you only have one of these ... right?            01/01/70 00:00      
                     beware            01/01/70 00:00      
                        Interesting concept            01/01/70 00:00      
                        Don't think so            01/01/70 00:00      
                           make a FULL schematic            01/01/70 00:00      
                              Of course            01/01/70 00:00      
                           Careful, now!            01/01/70 00:00      
                     Diagram mis-labeled, sorry            01/01/70 00:00      
   Please consider that....            01/01/70 00:00      
      Lookup table            01/01/70 00:00      
         'Ohm" it out            01/01/70 00:00      
            I don't see how            01/01/70 00:00      
               then forget transistors            01/01/70 00:00      
         2-Anode 12-Cathode Drive Diagram            01/01/70 00:00      
            Thanks            01/01/70 00:00      
   It works like this....            01/01/70 00:00      
      Vbe, not Vce            01/01/70 00:00      
         that was probably I who did that ... and you're right            01/01/70 00:00      
            Well...            01/01/70 00:00      
               take a close look            01/01/70 00:00      
               I doubt it            01/01/70 00:00      
                  Possibly a radio section too            01/01/70 00:00      
                  Crystals            01/01/70 00:00      
                     That C### is a capacitor number, I think            01/01/70 00:00      
      How about this?            01/01/70 00:00      
         use PNP at the high side            01/01/70 00:00      
         ...And get rid of the extra resistor in the...            01/01/70 00:00      
            Thanks. Time to test and draw            01/01/70 00:00      
               multimeter solution            01/01/70 00:00      
                  Similar to what I did            01/01/70 00:00      

Back to Subject List