Oh no it isn't - 8052.com

Back to Subject List

Old thread has been locked -- no new posts accepted in this thread

??? 01/27/05 14:10 Read: times	#85933 - Oh no it isn't Responding to: ???'s previous message
	Panagiotis Gousis said: I wish I had access to an osilloscope.. This is the full circuit diagram... No it isn't thats the PCB layout. The circuit diagram shows how the blocks should be connected, the PCB layout is how they ARE connected. You design with a circuit diagram, which is an accurate record of your design and intentions, this is trnasferred to a PCB to implement the circuit. Steve

List of 34 messages in thread

Topic Author Date
Need programmer for DS89C430 & DS80C310              01/01/70 00:00
   The datasheet for 430 says:              01/01/70 00:00
   Or use a terminal program              01/01/70 00:00
   ... or do it the easiest way...              01/01/70 00:00
      It works fine              01/01/70 00:00
         Errata!              01/01/70 00:00
   Does NOT work!!!Help!              01/01/70 00:00
      Or can you tell me              01/01/70 00:00
         DS89C420 ISP              01/01/70 00:00
   Or maybe              01/01/70 00:00
      I meant crystall at 4 Mh.              01/01/70 00:00
      NOOOO              01/01/70 00:00
         Did you look at PCB Layout?              01/01/70 00:00
            No              01/01/70 00:00
               I don't understant much              01/01/70 00:00
   Heelpp!!              01/01/70 00:00
      bad title, bad link              01/01/70 00:00
         DS89C4x0 ISP              01/01/70 00:00
         About the link              01/01/70 00:00
            Link works here              01/01/70 00:00
      Link              01/01/70 00:00
         same place              01/01/70 00:00
   Link again              01/01/70 00:00
   Back to the main issue...              01/01/70 00:00
      No scope,              01/01/70 00:00
         But this is the FULL circuit diagram              01/01/70 00:00
            use something else              01/01/70 00:00
            Oh no it isn't              01/01/70 00:00
               Look at the bottom              01/01/70 00:00
                  but..              01/01/70 00:00
                     Cap on Pin 2 to connected Vcc              01/01/70 00:00
                        which goes to show.....              01/01/70 00:00
                           You 're right              01/01/70 00:00
                              Make a start.              01/01/70 00:00

Back to Subject List

Topic	Author	Date
Need programmer for DS89C430 & DS80C310		01/01/70 00:00
The datasheet for 430 says:		01/01/70 00:00
Or use a terminal program		01/01/70 00:00
... or do it the easiest way...		01/01/70 00:00
It works fine		01/01/70 00:00
Errata!		01/01/70 00:00
Does NOT work!!!Help!		01/01/70 00:00
Or can you tell me		01/01/70 00:00
DS89C420 ISP		01/01/70 00:00
Or maybe		01/01/70 00:00
I meant crystall at 4 Mh.		01/01/70 00:00
NOOOO		01/01/70 00:00
Did you look at PCB Layout?		01/01/70 00:00
No		01/01/70 00:00
I don't understant much		01/01/70 00:00
Heelpp!!		01/01/70 00:00
bad title, bad link		01/01/70 00:00
DS89C4x0 ISP		01/01/70 00:00
About the link		01/01/70 00:00
Link works here		01/01/70 00:00
Link		01/01/70 00:00
same place		01/01/70 00:00
Link again		01/01/70 00:00
Back to the main issue...		01/01/70 00:00
No scope,		01/01/70 00:00
But this is the FULL circuit diagram		01/01/70 00:00
use something else		01/01/70 00:00
*Oh no it isn't*		01/01/70 00:00
Look at the bottom		01/01/70 00:00
but..		01/01/70 00:00
Cap on Pin 2 to connected Vcc		01/01/70 00:00
which goes to show.....		01/01/70 00:00
You 're right		01/01/70 00:00
Make a start.		01/01/70 00:00