Email: Password: Remember Me | Create Account (Free)

Back to Subject List

Old thread has been locked -- no new posts accepted in this thread
???
11/14/06 09:15
Read: times


 		 #127942 - How to post legible code
Responding to: ???'s previous message
For instructions on how to post code, see: http://www.8052.com/users/jonled/noob.pdf
Read the section on page 3 under the title, "Posting Code" - the use of the 'pre' and '/pre' tags is described and clearly illustrated

One thing to note: use only spaces to layout your code; do not use TABs.

And remember to use the 'Preview' button to check it before your press 'Post' !

List of 44 messages in thread
TopicAuthorDate
fx2 serial port mode0            01/01/70 00:00      
   How to post legible code            01/01/70 00:00      
      I dunno            01/01/70 00:00      
      thanks            01/01/70 00:00      
         who is is this microresistor expert?            01/01/70 00:00      
         You, too, can be expert!            01/01/70 00:00      
            well, I did            01/01/70 00:00      
               But of course, you prefer to be obtuse            01/01/70 00:00      
                  no, I am not 'obtuse', just trying to get to the s            01/01/70 00:00      
   Legible code posted,please continue the discussion            01/01/70 00:00      
      That's better            01/01/70 00:00      
         rxd0out            01/01/70 00:00      
            REN_0            01/01/70 00:00      
         I'm puzzled            01/01/70 00:00      
            Bible Time!            01/01/70 00:00      
               Separate RXD0OUT pin            01/01/70 00:00      
                  Now I'm confused, too!            01/01/70 00:00      
                  data is not transmitting            01/01/70 00:00      
               OUCH!            01/01/70 00:00      
                  1Mhz clock            01/01/70 00:00      
                     reply            01/01/70 00:00      
   why no body is replying            01/01/70 00:00      
      Richard, where are you, he is using mode 0!            01/01/70 00:00      
         I didn't have anything to contribute ...            01/01/70 00:00      
      Because no particular error            01/01/70 00:00      
         RxD0out            01/01/70 00:00      
            Debug monitor?            01/01/70 00:00      
               connected to SI0-0            01/01/70 00:00      
                  Debug monitor!!            01/01/70 00:00      
                     mode1            01/01/70 00:00      
                        monitor switches the UART mode            01/01/70 00:00      
                           Tested with SIO-1            01/01/70 00:00      
                              Monitor comes from EEPROM?            01/01/70 00:00      
                                 problem solved            01/01/70 00:00      
                                    Not yet            01/01/70 00:00      
                                       12Mhz            01/01/70 00:00      
                                          Then what was the cause, after all?            01/01/70 00:00      
                                             Don't leave it unsolved            01/01/70 00:00      
                                                ALLOCATE_EXTERN??            01/01/70 00:00      
                                                   ALLOCATE_EXTERN fixes FX2 xdata registers addr            01/01/70 00:00      
                                                      EXTERN ALLOCATE            01/01/70 00:00      
                                                         ALLOCATE_EXTERN fixes PORTECFG address            01/01/70 00:00      
                                                            EXTERN_ALLOCATE            01/01/70 00:00      
                                                               Its ALLOCATE_EXTERN .not EXTERN_ALLOCATE            01/01/70 00:00      

Back to Subject List