Email: Password: Remember Me | Create Account (Free)

Back to Subject List

Old thread has been locked -- no new posts accepted in this thread
???
02/06/07 18:18
Read: times


 		 #132155 - You mean like...
Responding to: ???'s previous message
I did all this without any luck...

http://www.8052.com/forum/read.phtml?id=101594

1. File all the edges (top and bottom [8 sides total]) of the PCB with a flat file. This makes sure the iron will meet all of the printed circuit board. This is the single most important step.

2. Clean the PCB with the 200 grit sand paper. 10 seconds of sanding is all you need. Wipe off with paper towel.

3. Place the Toner Transfer on the PCB. Place a piece of typing paper over the Toner Transfer and iron for two to three minutes. Don't put a lot of pressure on the iron. Just move it back and forth on all sides.

4. Let the PCB cool for about five minutes and pry the toner transfer off of the PCB.

List of 42 messages in thread
TopicAuthorDate
My 8051 project failed. Help me recover please.            01/01/70 00:00      
   Wrong questions            01/01/70 00:00      
      omg            01/01/70 00:00      
         You\'re looking in the wrong place            01/01/70 00:00      
            I explain            01/01/70 00:00      
   under-/overexposure?            01/01/70 00:00      
   Test exposure            01/01/70 00:00      
      Nice...            01/01/70 00:00      
   Developer            01/01/70 00:00      
      If you're using software ...            01/01/70 00:00      
         answer            01/01/70 00:00      
            How do you transfer your image to the board?            01/01/70 00:00      
               done            01/01/70 00:00      
                  Just how do you know that?            01/01/70 00:00      
                     answer            01/01/70 00:00      
                        You need to examine it with a microscope.            01/01/70 00:00      
                        Been there done that.            01/01/70 00:00      
      Hypering ?            01/01/70 00:00      
         hypering            01/01/70 00:00      
            Future is...dark ?            01/01/70 00:00      
   Press-N-Peel            01/01/70 00:00      
      Maybe...            01/01/70 00:00      
      nah            01/01/70 00:00      
         Iron on...            01/01/70 00:00      
            Me too...            01/01/70 00:00      
               Me Three ...            01/01/70 00:00      
                  Press-N-Pell works GREAT!            01/01/70 00:00      
                     You mean like...            01/01/70 00:00      
   ABOUT THE DISTANCE BEETWEEN 2PIN            01/01/70 00:00      
      2.5mm?            01/01/70 00:00      
         Read the score - he's wrong!            01/01/70 00:00      
      Exclusive limit            01/01/70 00:00      
         Elusive truths ...            01/01/70 00:00      
            Very true.            01/01/70 00:00      
               With one layer, well the reg problems go away            01/01/70 00:00      
         width            01/01/70 00:00      
            Port?            01/01/70 00:00      
               answer            01/01/70 00:00      
                  They are Connectors - not Ports            01/01/70 00:00      
                  FYI - Those are shell-sizes            01/01/70 00:00      
                     FYFI - It still is the standard            01/01/70 00:00      
                     The same script            01/01/70 00:00      

Back to Subject List