Email: Password: Remember Me | Create Account (Free)

Back to Subject List

Old thread has been locked -- no new posts accepted in this thread
???
06/14/08 11:58
Read: times


 		 #155908 - Richard??
Responding to: ???'s previous message
I'd suggest a low (33-75 ohm) resistance in series with Vcc, and a 1 nf plus a 10 uF on either side of the resistor. Likewise on the GND side, but with the total capacitance in the range I mentioned.

This is fuzzy. I read that you want to insert resistors in series with the ground pins (which I'm sure you don't) and where does the other side of the 'likewise' caps go?

The jury is out on this one, some use a small resistor in series with Vcc, I never do. I can see the purpose, but do not see the need. I think the negative effect of the resistor outweighs the positive.

Erik


List of 45 messages in thread
TopicAuthorDate
I'm getting insane! pls help!            01/01/70 00:00      
   I do not know much about Arghmel, but            01/01/70 00:00      
      >Arghmel<, Erik, are you crazy?            01/01/70 00:00      
         fair warning to all            01/01/70 00:00      
   Thanks for the props but....            01/01/70 00:00      
      have you tried changing the chip            01/01/70 00:00      
   Yep            01/01/70 00:00      
      the Arghmel users should wake up soon            01/01/70 00:00      
         The Problem Often Is The ...            01/01/70 00:00      
            I'll try that            01/01/70 00:00      
               But....            01/01/70 00:00      
                  What breed of MAX232?            01/01/70 00:00      
                     so...            01/01/70 00:00      
                        Trainer Board            01/01/70 00:00      
                           um quite similar...            01/01/70 00:00      
                        Your schema looks fine            01/01/70 00:00      
                           a strange thing has happened            01/01/70 00:00      
                              470uF            01/01/70 00:00      
                                 Just wanted to state the same            01/01/70 00:00      
                              It would have to be a very good 470uF cap ...            01/01/70 00:00      
                                 Richard??            01/01/70 00:00      
                                    What negative effect would that be?            01/01/70 00:00      
                                       let's do that, you start            01/01/70 00:00      
                        DEAD wrong            01/01/70 00:00      
   Oh uh......            01/01/70 00:00      
      Wrong Xtal may be            01/01/70 00:00      
         0.1uF ok then            01/01/70 00:00      
            Are you sure?            01/01/70 00:00      
               I found a usable one            01/01/70 00:00      
                  Did you find the reason            01/01/70 00:00      
                     still searching for the reason            01/01/70 00:00      
            Model of a capacitor            01/01/70 00:00      
         18.432MHz for Std Baud Rates ...            01/01/70 00:00      
   Shorts,shorts,shorts,            01/01/70 00:00      
      Pictures?            01/01/70 00:00      
         why is that?            01/01/70 00:00      
            Just Curious            01/01/70 00:00      
               Hey uh Jon i had already removed all socketed ICs            01/01/70 00:00      
      Vss for logical chips SHOULD be ground            01/01/70 00:00      
         Stupid me, i meant Vcc not Vss            01/01/70 00:00      
         Let\'s call this a day            01/01/70 00:00      
            Good Luck!            01/01/70 00:00      
               Thank you all            01/01/70 00:00      
   Boot loader running?            01/01/70 00:00      
      I'll try it tonight            01/01/70 00:00      

Back to Subject List