Email: Password: Remember Me | Create Account (Free)

Back to Subject List

Old thread has been locked -- no new posts accepted in this thread
???
11/15/05 18:23
Read: times


 		 #103763 - Kai, I did not think you did
Responding to: ???'s previous message
Erik, there's no disagree with you. Please read again the original post, especially
Kai, I did not think you did. You stated that the 3 resistor was not "noise proof" and since nothing is, that is, of course, the case.

However, re my first post, the OP did the "usual" in attempting to do 485 without reading "10 ways to bulletproof". That should be MANDATORY before even writing the first line of code ot drawing the first line of the schematic if 485 is involved.

While cost conciousness is admirable This leads me to think that maybe I don't ever need to ... in order to save 2 or 4 resistors (3 res term in one or both ends) is ludicrous.

Erik


List of 34 messages in thread
TopicAuthorDate
RS485 Question            01/01/70 00:00      
   drive capacity            01/01/70 00:00      
      3 resistor termination            01/01/70 00:00      
         Only if you have power to burn            01/01/70 00:00      
            15 milliwatts. A lot of power?            01/01/70 00:00      
               Depends on your application            01/01/70 00:00      
                  how are you going to terminate at that            01/01/70 00:00      
                  RS485 loops are hungry...            01/01/70 00:00      
      You will loose all the noise margin!            01/01/70 00:00      
         not if you use 3 resistor termination            01/01/70 00:00      
            Better, but...            01/01/70 00:00      
               works for me, what do you have that is b            01/01/70 00:00      
                  No disagree...look what weird is planned            01/01/70 00:00      
                     Kai, I did not think you did            01/01/70 00:00      
                        Clarification            01/01/70 00:00      
                           3 resistors or not            01/01/70 00:00      
                              Then is all fail-safe bad?            01/01/70 00:00      
                                 Can you see the difference?            01/01/70 00:00      
                                    Kai, you keep ignoring the fact that RS4            01/01/70 00:00      
                                       I ignore nothing            01/01/70 00:00      
                                          It's the best we have and it works when            01/01/70 00:00      
                                             Yes, but it can fail from time to time            01/01/70 00:00      
                                                I have handled that with isolated RS485            01/01/70 00:00      
                                                   We do already            01/01/70 00:00      
                                                      485-422            01/01/70 00:00      
                                                         I challenge you to find a RS422 driver            01/01/70 00:00      
                                                            In the past.            01/01/70 00:00      
                                 All fail safe is good and 0.25V is plent            01/01/70 00:00      
                           That is not RS485, that is J1708            01/01/70 00:00      
                              trick to get around pseudo non random            01/01/70 00:00      
                                 This won't really help.            01/01/70 00:00      
                              Helpful            01/01/70 00:00      
                                 I am doing that using the Dallas DS2401            01/01/70 00:00      
                                    Yes that is what I am planning            01/01/70 00:00      

Back to Subject List