Email: Password: Remember Me | Create Account (Free)

Back to Subject List

Old thread has been locked -- no new posts accepted in this thread
???
07/22/05 16:10
Read: times


 		 #97831 - Sorry my mistake ...
Responding to: ???'s previous message
Farshid Jafari Harandi said:
As Andy said , 3.9M ohm is too high , use 10k to 100k . again as Andy said ,if you are using Port 0 you could simply use a pullup to the 3.3V supply for your outputs

By that i meant a 10k-100k pullup to the 3.3V line.

Sorry for the confusion

Farshid J.H.

List of 46 messages in thread
TopicAuthorDate
Timing Firmware!            01/01/70 00:00      
   Err - read the datasheet!            01/01/70 00:00      
      Err - read the datasheet!            01/01/70 00:00      
         I don't understand the problem            01/01/70 00:00      
            dont scare            01/01/70 00:00      
               Jan & Russell            01/01/70 00:00      
                  get a dev board, there is much to learn            01/01/70 00:00      
         simple            01/01/70 00:00      
            Thanks!!!            01/01/70 00:00      
            Not as simple as you said Jan!            01/01/70 00:00      
               not, if you are very sneeky            01/01/70 00:00      
               ignored address            01/01/70 00:00      
                  Thanks Jan            01/01/70 00:00      
   different datasheet            01/01/70 00:00      
   Absolute Maximum Ratings!            01/01/70 00:00      
      3.3V?            01/01/70 00:00      
         3.3 V ??            01/01/70 00:00      
            3.3 V ??            01/01/70 00:00      
               Search Time!            01/01/70 00:00      
                  I agree...            01/01/70 00:00      
                     Dear mehdi            01/01/70 00:00      
                        Thanks            01/01/70 00:00      
                           expensive for large amount of production            01/01/70 00:00      
                              expensive for large amount of production            01/01/70 00:00      
                     Issues - not chips            01/01/70 00:00      
               5V to 3.3V solution            01/01/70 00:00      
                  Eh?            01/01/70 00:00      
                     Andy you are accurate!            01/01/70 00:00      
                  3.9M !!            01/01/70 00:00      
                     Answer Is Wrong!!!!            01/01/70 00:00      
                        that is unsafe and depending on the othe            01/01/70 00:00      
                           I agree...            01/01/70 00:00      
                              I'm at a loss            01/01/70 00:00      
                        Sorry my mistake ...            01/01/70 00:00      
                           rock solid 3.3 to 5            01/01/70 00:00      
         Design decisions.            01/01/70 00:00      
            top-bottom vs. bottom-top            01/01/70 00:00      
   Confidential information?            01/01/70 00:00      
      Andy!            01/01/70 00:00      
   Russell & Jan            01/01/70 00:00      
   0 ohm Resistor?            01/01/70 00:00      
      Isn't it obvious?            01/01/70 00:00      
         EVB!            01/01/70 00:00      
            Star Point            01/01/70 00:00      
               Furthermore            01/01/70 00:00      
      common GND            01/01/70 00:00      

Back to Subject List