Email: Password: Remember Me | Create Account (Free)

Back to Subject List

Old thread has been locked -- no new posts accepted in this thread
???
02/08/08 10:36
Read: times


 		 #150463 - yes i agree..
Responding to: ???'s previous message
Andy Neil said:
What, exactly, do you mean by, "a lot"?

noise ripple is in excess of 200mV.its really fuzzy.

Andy Neil said:

shouldn't it be a straight 5V DC

yes, it should - and if it isn't, you have a fundamental problem!

yup. i realize that :(
Andy Neil said:
There is no point in going any further with test programs or anything else until you have a good, clean, stable power supply!

well, i agree i should have tested the board before i took the plunge..but the reason i even hooked up the circuit to the scope is because of its strange behavior with edge triggering.The external interrupt would trigger at the rising and falling edge of my input ( to P3.2- int0)





List of 58 messages in thread
TopicAuthorDate
problems with edge triggering and noise            01/01/70 00:00      
   5v regulator,capacitors - elko and creamic            01/01/70 00:00      
      not likely            01/01/70 00:00      
         not true!            01/01/70 00:00      
   How much noise?            01/01/70 00:00      
      using a 78L05 voltage regulator IC with 220 uF cap            01/01/70 00:00      
         be conservative ... for now ...            01/01/70 00:00      
   First things first - Begin at the beginning            01/01/70 00:00      
      yes i agree..            01/01/70 00:00      
         photo            01/01/70 00:00      
            Well done            01/01/70 00:00      
               the "backside" :)            01/01/70 00:00      
                  Use Solder Wick as Braid            01/01/70 00:00      
                     is this ok?            01/01/70 00:00      
                        i found this strange looking woven wire?            01/01/70 00:00      
                  Perf Board Types            01/01/70 00:00      
                  Pad-Per-Hole PTH            01/01/70 00:00      
                     How much ?            01/01/70 00:00      
                        This Much            01/01/70 00:00      
                           other boards            01/01/70 00:00      
                     Here\'s what I prefer.            01/01/70 00:00      
            it looks quite acceptable, with caveats ...            01/01/70 00:00      
      How much noise!            01/01/70 00:00      
   Regulator problems..            01/01/70 00:00      
      sorry wrong measurements            01/01/70 00:00      
         Actuall, you were right, in part ...            01/01/70 00:00      
            Different caps..            01/01/70 00:00      
      one more issue            01/01/70 00:00      
         7805            01/01/70 00:00      
            Swop the pins around !!            01/01/70 00:00      
            agreed            01/01/70 00:00      
               what about switching noise and ripple?            01/01/70 00:00      
                  to RE            01/01/70 00:00      
                     This is a real disappointment            01/01/70 00:00      
                        numbers            01/01/70 00:00      
                           that's not what was asked ...            01/01/70 00:00      
                              yes and no            01/01/70 00:00      
                                 I've got lots of those ...            01/01/70 00:00      
                                    not mostly - only and who cares            01/01/70 00:00      
                                       It's what's before the filter that matters!            01/01/70 00:00      
                                          enough            01/01/70 00:00      
                                             not exactly ...            01/01/70 00:00      
                                                as stated before            01/01/70 00:00      
                                                   Nonsense!            01/01/70 00:00      
                                                      you can't stop, can you            01/01/70 00:00      
                                                         I love to see Erik backpedal            01/01/70 00:00      
                                                            Better start giving a hoot            01/01/70 00:00      
                                                               as stated so often, I DO give a hoot ...            01/01/70 00:00      
                                                                  as stated so often, I DO give a hoot ...            01/01/70 00:00      
                                                                     I think you are right            01/01/70 00:00      
                                                                        I too favour looking inside black boxes            01/01/70 00:00      
                                                                           blindly?            01/01/70 00:00      
                                                                              Erik ... you\'re headed for a disappointment            01/01/70 00:00      
                                                                                 If you accept datasheet blindly I cant help            01/01/70 00:00      
                                                                                    you do not get the point, do you?            01/01/70 00:00      
                                                                     not exactly            01/01/70 00:00      
                                                                        I never made any such claim            01/01/70 00:00      
         gee ... that's a negative regulator ...            01/01/70 00:00      

Back to Subject List