Email: Password: Remember Me | Create Account (Free)

Back to Subject List

Old thread has been locked -- no new posts accepted in this thread
???
01/04/08 16:31
Read: times


 		 #149048 - and thus
Responding to: ???'s previous message
the '810 has a pushpull output...
and thus, depending in the value of 'R' pushing the reset button will either have no effect or smoke the 810.

I dislike Atmel and do thus not know if your processor uses RST or _RST, in the case of _RST use an open collector supervisor and a resistor to Vcc and a switch to gnd, in the case of RST use two, say 1k, resistors in series between the super and the uCs RST input (CMOS does not use much current) and switch the middle to Vcc.

Erik


List of 56 messages in thread
TopicAuthorDate
8051 First time user schematic check            01/01/70 00:00      
   a perfunctionary check            01/01/70 00:00      
      And            01/01/70 00:00      
      suporvisor chip            01/01/70 00:00      
         re: Supervisor chip            01/01/70 00:00      
         go to maxim            01/01/70 00:00      
            Thanks/New Schematic            01/01/70 00:00      
               Supervisor Wrong            01/01/70 00:00      
                  You could have it wired up an running by now.            01/01/70 00:00      
                     and thus            01/01/70 00:00      
               the power LED has no series resistor            01/01/70 00:00      
               The MAX232 +10V Capacitor            01/01/70 00:00      
   Another hint            01/01/70 00:00      
      port 0 pins            01/01/70 00:00      
   startup project advise            01/01/70 00:00      
      Incrimental Stages....            01/01/70 00:00      
      thanks            01/01/70 00:00      
         a comment            01/01/70 00:00      
            Agree            01/01/70 00:00      
               why schematics???            01/01/70 00:00      
               lucky you            01/01/70 00:00      
   assembly            01/01/70 00:00      
      re SILabs devboards            01/01/70 00:00      
      yes, why not            01/01/70 00:00      
         suffer            01/01/70 00:00      
   check            01/01/70 00:00      
      even worse            01/01/70 00:00      
      Ground Symbol            01/01/70 00:00      
         beware of idiots            01/01/70 00:00      
            Great Example            01/01/70 00:00      
               PCB class            01/01/70 00:00      
               Agreed, but            01/01/70 00:00      
                  Advice for someone just starting            01/01/70 00:00      
            idiocracy            01/01/70 00:00      
         regarding ground vcc symbols            01/01/70 00:00      
   Serial port pins            01/01/70 00:00      
      reply to Esko            01/01/70 00:00      
         we are here to help            01/01/70 00:00      
      Thanks for the reply            01/01/70 00:00      
   you will have hard time...            01/01/70 00:00      
      serial port connections            01/01/70 00:00      
         serial port connections II            01/01/70 00:00      
            a vbery common mistake/confusion            01/01/70 00:00      
               ... plus the infinite variations...            01/01/70 00:00      
         Opinion            01/01/70 00:00      
            a comment on the comment            01/01/70 00:00      
               SPI            01/01/70 00:00      
   One more development card argument            01/01/70 00:00      
      sure, but do you get ICE functionality?            01/01/70 00:00      
         No ICE but wire wrap is OK            01/01/70 00:00      
            and so what            01/01/70 00:00      
               To learn ?            01/01/70 00:00      
                  learning - modifying SMT            01/01/70 00:00      
                     Bino microscope            01/01/70 00:00      
                        not to worry            01/01/70 00:00      
                        site showing how to solder/desolder SMT'S            01/01/70 00:00      

Back to Subject List